# The Mysterious dB of Fiber Optics

Whenever tests are performed on fiber optic networks, the results are displayed on a meter readout in dB. Optical loss is measured in dB while optical power is measured in dBm. Loss is a negative number (like -3.2 dB), as are most power measurements. Confused? Many fiber optic techs are too. Let’s see if we can clear up some of the confusion.

When we make fiber optic measurements, we are quantifying the power in the light measured. The standards we use for power measurements, maintained by the United States National Institute of Standards and Technology, are actually determined by the heating effect of the light as it is absorbed in a detector. Every fiber optic power meter sold is calibrated traceable to the NIST standard, so different meters should measure the same power, within the limits of calibration uncertainty.

Optical power in fiber optics is similar to the heating power of a light bulb, just at much lower power levels. While a light bulb may put out 100W, most fiber optic sources are in the milliwatt to microwatt range (0.001 to 0.000001W), so you won’t feel the power coming out of a fiber and it is generally not harmful.

In the early days of fiber optics, source output power was usually measured in milliwatts and loss was measured in deciBels or dB. Over the years, all measurements migrated to dB for convenience. This was when the confusion began.

Loss measurements were generally measured in dB, since dB is a ratio of two power levels, one of which is considered the reference value. The dB is a logarithmic scale (remember “logs” from high school math?) where each 10 dB represents a ratio of 10. The actual equation used to calculate dB is: dB = 10 log (measured power/reference power). So 10 dB is a ratio of 10 (either 10 times as much or 1/10 as much), 20 dB is a ratio of 100, 30 dB is a ratio of 1,000, etc. When the two powers are equal, dB = zero—a result of the log scale used, but a convenient value that’s easily remembered.

If we have loss in a fiber optic system, the measured power is less than the reference power, so the ratio of measured power to reference power is less than 1 and the log is negative, making dB a negative number. When we set the reference value, the meter reads “0 dB” because the reference value we set and the value the meter is measuring is the same. Then when we measure loss, the power measured is less, so the meter will read “-3.0 dB” for example, if the tested power is half the reference value. Although meters measure a negative number for loss, convention has us saying the loss is a positive number, so we say the loss is 3.0 dB when the meter reads -3.0 dB.

Measurements of optical power are expressed in units of dBm. The “m” in dBm refers to the reference power, which is 1mW. Thus a source with a power level of 0 dBm has a power of 1mW. Likewise, -10 dBm is 0.1mW and +10 dBm is 10mW.

Instruments that measure in dB can be either optical power meters or optical loss test sets (OLTS). The optical power meter usually reads in dBm for power measurements or dB with respect to a user-set reference value for loss. While most power meters have ranges of +3 to -50 dBm, most sources are in the range of 0 to -10 dBm for lasers and -10 to -20 dBm for LEDs. Only lasers used in CATV or long-haul telephone systems have enough power to be really dangerous—up to +20 dBm, which translates to 100mW or 1/10 of a Watt.

The OLTS or the power meter on the dB scale measures relative power or loss with respect to the reference level set by the user. The range they measure will be determined by the output power of the source in the unit and the sensitivity of the detector. For multimode fiber, an OLTS using a LED source will usually measure over a range of 0 to 30 dB, more than adequate for most multimode cable plants, which are under 10 dB loss. Singlemode networks use lasers and may have loss ranges of up to 50 dB for long-haul telecom systems, but campus cabling using singlemode may only have 1-3 dB loss. Thus a singlemode OLTS may be different for short and long systems.

If you remember that dB is for measuring loss, dBm is for measuring power and the more negative a number is, the higher the loss, it’s hard to go wrong. Set your zero before measuring loss and check it occasionally while making measurements. EC

HAYES is a VDV writer and trainer and the president of The Fiber Optic Association. Find him at www.JimHayes.com.