Advertisement

Advertisement

Getting It Right: Training helps technicians on the job

By Wayne D. Moore | Nov 17, 2026
AdobeStock_549947145
It seems that no matter where I go, I get asked the same question: “Why can’t more technicians get it right?”

Advertisement

Advertisement

Advertisement

Advertisement

Advertisement

I get to meet a lot of great fire alarm system technicians and installers as I travel throughout the country. And it seems that no matter where I go, I get asked the same question: “Why can’t more technicians get it right?”

This question, of course, comes from the unfortunate fact that too few installers and technicians have the necessary training and code background to install a fire alarm system correctly the first time—or, in some cases, at all. What does it take in today’s more complex fire alarm market to get it right?

In my opinion, there is a disconnect between the knowledge required to perform as a craftsman and what technicians today think they need to know. Not too many years ago, technicians would start with a fire alarm installing company, usually as a helper, and learn basic electrical installation techniques. The owner would encourage the helper to take classes in electricity theory. Helpers would also participate in installations, learning through on-the-job training from experienced journeymen.

Hopefully, the helper would have access to code seminars, including on NFPA 72 and NFPA 70. Technicians would also have training opportunities from the manufacturers whose equipment they installed. After a few years, they would understand the nuances of the equipment and how the codes and standards affected those installations.

Today’s technicians may not begin their career by installing fire alarm systems in buildings. Instead, they may work as a programmer and not be needed at a site until it is time to program the fire alarm control unit. Technicians may also assume they do not need to know what constitutes a “workmanlike manner” or a code­-compliant installation because they focus only on programming.

If they must have all the skills outlined above—good workmanship, programming skills and knowledge of equipment installation, basic code and standards, basic electricity and electrical installation—getting it right can become a daunting task!


Training is the answer

So back to the question: “Why can’t more technicians get it right?” The answer is that installation company owners must be committed to providing appropriate training, and technicians must participate in it and have a passion for doing what is right.

Training techs is the first step. I have heard many excuses about why some companies don’t do this. Some owners respond, “If I train my technicians, they will just leave and go to the competition!” My answer has always been the same: if you don’t train them and keep them, what will that cost? Does that mean your company will always have untrained employees? Think about that. 

Perhaps the key to keeping employees is offering more training than they can get elsewhere. If they are better trained, the owners will have to pay them better, but doesn’t that make sense? If they are better trained, they will make fewer mistakes, be more efficient and be more loyal to the company that pays them fairly. 

With new employees, you pay more if they already have experience and training. Why not develop them yourself and train them in the way you think is right? The adage of being penny-wise and pound-foolish comes to mind. Untrained technicians will always be more costly in the long term.

Getting it right starts with commitment from the owner, who is often the first journeyman who trains the first helper. The owner must have received proper training, fully understand the applicable codes, standards and basic electrical techniques, and already know what “workmanlike” installations look like. The owner must already understand the importance of working with the authority having jurisdiction (AHJ) and prove that, when they ask an AHJ for an inspection, the job’s readiness warrants that inspection. They never waste an AHJ’s time with “almost ready” installations.

Getting it right also means taking advantage of all the training equipment manufacturers offer. 

Getting it right means becoming aware of software issues that can arise during a system installation, the latest revisions to that software and why the manufacturer made them.

Getting it right means understanding the requirements of the codes and standards and employing the correct installation methods to ensure an installation meets those requirements.

And, finally, getting it right means taking the time to learn how to install a fire alarm system correctly.

stock.adobe.com/kelvn

About The Author

MOORE, PE, is a licensed professional fire protection engineer, and located in Jamestown, R.I. He is the editor of five editions of the National Fire Alarm Code Handbook. He authored, “Designing Mass Notification Systems – A Pathway to Effective Communications.” He is a principal member of the NFPA 72 Correlating Committee and former chair, now principal member, of the Emergency Communications System Technical Committee. He can be reached at [email protected].

 

Advertisement

Advertisement

Advertisement

Advertisement

featured Video

;

3M - Science. Applied to Life.

Advertisement

Related Articles

Advertisement